Small Fragment Implant & Instrument Set Manufacturers

Small Fragment Implant & Instrument Set

[ Model No. GOS1408 ]

Product Availability: In Stock

Send Inquiry

Request a Catalog

We supply and ship our products worldwide!

All Our products are CE marked and FDA approved.

GOS1408	Small Fragment Implant & Instrument Set
BTD1130.25.130	Drill Bit, Dia. 2.5, Q.C.	2
BTD1130.35.130	Drill Bit, Dia. 3.5, Q.C.	2
IBS700.03	Counter Sink for 3.5, 4.0 mm Screw (6.0 Head)	1
C-IBS762.35	Cortical Tap for 3.5 mm Screws, Q.C.	2
C-IBS762.351	Cancellous Tap for 3.5 mm Screw Q.C.	1
C-IBS762.40	Cancellous Tap for 4.0 mm Screws, Q.C.	1
IBS765	Quick Coupling Handle	1
IBS721.35	Tap Sleeve, 3.5 mm Diameter/Drill Sleeve 2.5 mm Diameter	1
IBS720.27	Insert Sleeve Diameter 3.5 mm/2.7 mm	1
C-ILBS747.25	Small Screwdriver, 3.5 mm	1
ILBS746.25	Small Screwdriver Shaft, 2.5 mm Hex., Quick Coupling End	1
IBS709	Small Depth Gauge	1
IBS775	Neutral and Load Drill Guide, 2.5/3.5 mm	1
	General Instruments
REH1053	Sharp Hook	1
IBS771	Holding Clip for Plates	2
IBS753	Self-Holding Screw Forceps	1
IBP630.01	Plate Bender for Small DCP	2
GOS124	Bending templates, 5 and 7 holes, 1 pair	2
BHF1246.19	Self-Centering Bone Holding Forceps,190 mm	1
BHF1245.17	Reduction Forceps with points, 170 mm Thread Lock	1
BHF1248.17	Reduction Forceps Serrated Thread Lock 170 mm	1
REH1064.06.160	Small Retractor, 6 mm Width	1
REH1064.08.160	Small Retractor, 8 mm Width	1
REH1064.15.160	Retractor for Small Fragments, with Broad Shank Long	2
REH1068.06S	Small Periosteal Elevator, with Straight Edge, 6 mm Width	1
	IMPLANTS
	Cortex Screws, Diameter 3.5 mm	Units (each size)
713.10 - 713.28	10 mm - 28 mm (Increment of 2 mm)	4
713.32 - 713.40	32 mm - 40 mm (Increment of 4 mm)	4
	Cancellous Screws 3.5 mm, Fully Threaded	Units (each size)
725.12 - 725.30	12 mm - 30 mm (Increment of 2 mm)	2
725.35 - 725.60	35 mm - 60 mm (Increment of 5 mm)	2
	Cancellous Screws 4.0 mm, Short Thread	Units (each size)
723.12 - 723.30	12 mm - 30 mm (Increment of 2 mm)	2
723.35 - 723.50	35 mm - 50 mm (Increment of 5 mm)	2
759	Washer 4 mm	2
	One Third Tubular Plates
639.02	2 Holes	1
639.03	3 Holes	1
639.04	4 Holes	2
639.05	5 Holes	2
639.06	6 Holes	2
639.07	7 Holes	1
639.08	8 Holes	1
	Dynamic Compression Plates 3.5 mm
617.06	6 Holes	2
617.08	8 Holes	2
617.1	10 Holes	1
	T-plates with 3 Thead Holes 3.5 mm
643.03	3 Holes	1
643.04	4 Holes	1
627	T-plates, Oblique Angled 3.5 mm
627.03L	3 Holes, Left	1
627.03R	4 Holes, Right	1
PS911D	Kirschner Wires, 10 each 1.25/1.6/2.0 mm Dia, Length 150 mm	30
	Screw Rack	1
AGC1408	Aluminium Graphic Case	1